GRAPHTEC FC8000 MANUAL PDF

Vinyl Cutter Download Graphtec FC, Vinyl Cutter Machine Download Software Installation & Operation Manual in pdf ( MB) > Download Now. Manually Adjusting the FC ARMS Sensor Level for Glossy Media and Glossy Laminated Prints. When using some glossy media or when using glossy. View and Download GRAPHTEC FC Series user manual online. Cutting Pro . FC Series Plotter pdf manual download.

Author: Gardami Nikolmaran
Country: Belarus
Language: English (Spanish)
Genre: Video
Published (Last): 13 September 2018
Pages: 59
PDF File Size: 6.9 Mb
ePub File Size: 1.9 Mb
ISBN: 605-4-38526-491-2
Downloads: 13200
Price: Free* [*Free Regsitration Required]
Uploader: Kagagul

When The Media Width Exceeds Mm When the Media Width Exceeds mm Position the three right-hand push rollers when the plotter is viewed from the Supplement front so that the left and right push rollers are at the edges and the middle The media must always be positioned over the push roller in the center of the media.

Graphtec Manuals and Drivers – SignWarehouse Product Support

If you desire to load the material from the front, it is also possible to use the front loading. Adjust the Blade Length Manually Optimal cut is not achieved unless the blade length is adjusted in accordance to the used media and the cutter blade. R ollers that push the media against the grit rollers. It is not necessary when the plotter is connected using the USB cable. Maximum cutting distance of approximately m. T ool position move screen is displayed.

GRAPHTEC FC SERIES USER MANUAL Pdf Download.

Use magnifier or light pointer as a tool to match each points. Supplement TOOL setting screen is displayed. Use it turned off for all other cases. When the basket and Graphtec-specified media are graphtce under certain condition settings. Connect one end of the provided power cord to the FC AC line inlet and the other end to an electrical socket of the rated supply voltage.

  JABRA 9125 MANUAL PDF

Operate switches and sensors following the instructions on the screen. In this case, set the “: It is possible to set the origin point at the center when the HP- P. E It is over the setting range of the Reset to smaller value.

If there is no registration mark on the media, plot a registration mark first, scan that registration mark, plot another registration ,anual, and measure the difference of them. U sed to carry roll media and ensure its proper rotation.

GRAPHTEC FC8000 Series User Manual

Loupe adjusting The Position 14 – Loupe Adjusting the Position Axis Alignment, Cut Area Positioning loupe bombsight is used to align points for adjustment during axis alignment operations, and to align the corner points when specifying the plotting area.

When The Media Width Is To Mm Press the media lock to engage it, and then pull the leading edge out of the front of the plotter so that it completely covers the media sensor. Automatically Cross Cut will automatically cross cut after cutting when the cutting is done with provided software. Setting the Reference Angle The FC analyzes the cutting data, and fc88000 the angle of the cutter blade tip if the change in the angles of the corner is large.

  DIN 32501 PDF

Turn off this function for all other uses. Press the [1] key X. Preface In manuall to cutting marking film and other media, an FC series plotter can also be used as a pen plotter.

It will give graohtec or malfunction when it has made mistake. Always use the weaker setting for the push roller s between the two outside rollers. U sed to access various plotter functions. The cutting time in total becomes short if you set the TOOL UP SPEED to fast speed even though the speed of the tool when it is cutting lowered is set to slow speed for the hard to cut media hard or sticky. Comments to this Manuals Your Name.

Setting Initial Blade Direction Adjust The direction of blade is gtaphtec by making the blade touch the media right after the power is turned on, or after the pen condition is set.

graphtc Change the color of the registration mark. It improves the operation of the registration mark searching. Operation Turn the blade-length adjustment knob in the direction indicated by the arrow to retract the blade into the plunger. Following items are displayed in the default screen.