ASTM D4258 PDF

This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D on Protective. ASTM D Standard Practice for Surface Cleaning Concrete for Coating. ASTM D (Plastic sheet test): Place plastic sheet on concrete stab for 24 hours. o ASTM-D Standard Practice for Surface Cleaning Concrete for.

Author: Kanos Shaktik
Country: India
Language: English (Spanish)
Genre: Politics
Published (Last): 27 September 2017
Pages: 243
PDF File Size: 1.52 Mb
ePub File Size: 17.52 Mb
ISBN: 870-5-76132-841-6
Downloads: 10481
Price: Free* [*Free Regsitration Required]
Uploader: Torisar

Some composition boards may emit a waxy material that must be removed with a solvent prior to coating.

ASTM D – 05() – Standard Practice for Surface Cleaning Concrete for Coating

Check for compatibility by applying a test patch of the recommended coating system, covering at least 2 to 3 square feet. High-pressure water blasting is commonly used to clean substrates.

Subscription pricing is determined by: Add to Alert PDF. The steps below are provided for assistance in properly preparing various common substrates before coating. All loose mortar and foreign material should be removed from block. Here is a summary of some of the published standards with which installers and specifiers of corrosion protection linings should be familiar.

ASTM D4258 – 05(2017)

To avoid premature lining failures resulting from improper surface preparation, lining specifiers, applicators, and inspectors need to be familiar with these industry standards for surface preparation and to adhere to their principles in practice. When viewed without 4d258, a Near-White Blast Cleaned surface should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter, with the asrm of staining. Your Alert Profile lists the documents that will be monitored.

Make sure all visible grease, oil, salts, and soluble welding residues have been removed before hand tool cleaning by the methods outlined in SSPC-SP 1. Adherent mill scale, paint, and rust are not able to be removed by this process.

  ECONOMIC AND FINANCIAL DECISIONS UNDER RISK EECKHOUDT PDF

All loose rust, loose mill scale, loose and other detrimental foreign matter can be removed by power tool cleaning. Rooms must be heated in cold, damp weather. Ensure that knots and pitch streaks are scraped, sanded, and spot primed before a full priming coat is applied.

The surface to be coated must be clean and free of contaminants, oil, loose cement, mortar, and grease. Surface Preparation Proper surface preparation can improve the outcome of your coating system. Small residues of rust and paint may be left in the lower portions of pits if the original surface is pitted. So many corrosion protection lining projects succeed or fail with the quality of the surface preparation achieved before the lining is even installed.

When viewed without magnification, a metallic surface prepared according to this specification should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, astmm other foreign matter. This standard asgm also available to be asgm in Standards Subscriptions.

Remove all dust, oil, wax, grease, loose paint, mill scale, rust, dirt, mold, mildew, mortar, efflorensence, sealers, and other surface contaminants. Be advised that any coatings left on the surface to be painted may compromise the service length of the system.

Use an appropriate primer to spot prime any bare ares. Damaged areas must be repaired with an appropriate patching material.

Standard Practice for Surface Cleaning Concrete for Coating

Visible deposits of grease or oil must be removed prior to power tool surface preparation by any method specified in SSPC-SP 1, Solvent Cleaning, or other agreed upon methods. If the document is revised or amended, you will be notified by email.

  KENNETH CRAGG THE CALL OF THE MINARET PDF

If these requirements are ignored, the lining can delaminate from the substrate or fail to cure properly.

Make sure all spackled nail heads and tape joints are sanded smooth and all dust removed prior to painting. When c4258 is not possible or the surface has been treated with chromates or silicates, first Solvent Clean per SSPC-SP1 and apply a test area, priming as required. Patch all nail holes and imperfections with a wood filler or putty and sand smooth.

Thorough washing asym an abrasive cleanser will clean and dull in one operation, or, wash thoroughly and dull by sanding. We have no amendments or corrections for this standard.

As the voice of the U. Wood must be clean and dry.

ASTM D – 05 Standard Practice for Surface Cleaning Concrete for Coating

Make sure all visible grease, oil, salts, and soluble welding residues have been removed prior to power tool cleaning by the methods outlined in SSPC-SP 1. Following these guidelines will help ensure sufficient adhesion of the coating and can help prolong the life of the coating system. Standards Subsctiption may be the perfect solution.

Spackle the drywall defects. Maintenance painting will frequently not permit or require complete removal of all old coatings prior to repainting. Method of cleaning steel to remove dirt, oil, grease, loose rust, loose mill scale, and loose paint using water at pressures of 2, to 2, psi at a flow of 4 to 14 gallons per minute.

Allow the surface to dry thoroughly. Surface preparation methods as outlined in ASTM D are required if the coating system is incompatible. Proceed to Checkout Continue Shopping.